Processor Configurations

Speaker Files (.cpspkr) for Apex CloudPower amplifiers. They are suitable for use with amplifiers running firmware v1.2.1 or later, available on the CloudPower home page. Please download the User Manual for additional operating information.

CloudPower home page

User Manual

Apex CloudPower Presets 29Aug24 README.pdf

Apex CloudPower Presets 29Aug24.zip

Template files (.template.bin) for Ashly processors and mixer/amplifiers based on their AquaControl DSP engine.

AquaControl

Ashly AquaControl Templates 26Nov24 README.pdf

Ashly AquaControl Templates 26Nov24.zip

Voicing files (.voc) for Ashly DSP-enabled amplifiers and neXX00 Series processors were created with the Ashly Protea Software Suite. You must use v5.49 or later.
Note that the FIR filters in the Voicing files require the DSP to be set to a 48 kHz sample rate.

Ashly Protea Software Suite

Ashly 48k Voicings 17Sep24 README.pdf

Ashly 48k Voicings 17Sep24.zip

Custom Blocks for Fulcrum Acoustic loudspeakers were created with Biamp Tesira Version 4.10 software. They are suitable for use with Tesira SERVER and TesiraFORTE processors.

Note that AudiaFLEX and Nexia loudspeaker processor settings are no longer supported.

Biamp Tesira Version 4.10

Tesira Custom Blocks 29Aug24 README.pdf

Tesira Custom Blocks 29Aug24.zip

Speaker Presets for Fulcrum Acoustic loudspeakers were created for Blaze PowerZone™ Connect full Matrix DSP amplifiers using the embedded web app PowerZone™ Control. Firmware 1.4.0 or greater is required.

Blaze PowerZone™ Connect

Blaze PowerZone Connect Speaker Presets 30Sep24 README.pdf

Blaze PowerZone Connect Speaker Presets 30Sep24.zip

Settings for Fulcrum Acoustic loudspeakers are available for Dynacord electronics via SONICUE sound system software. They are suitable for use with IPX, L, and C series power amplifiers as well as the MXE5 matrix mix engine. The Fulcrum Acoustic Speaker Database is hosted by Dynacord and is immediately available when SONICUE software is installed.

SONICUE

Speaker Database

Fulcrum Acoustic Level 1 presets for Lab Gruppen PLM+ Series and D Series amplifiers plus LMX48 and LMX88 processors and are available as XP Module files (*.csm). They were created using Lake Controller Version 8.1.2 software and are available in the Lake XP Module Presets zip file found below. Please see the Lab Gruppen website for more information on each product. Note that the XP Module presets will not work in E, IPD, or legacy PLM Series amplifiers, nor Lake LM26/LM44 processors.

Lab Gruppen

Lake XP Module Presets 27Sep24 README.pdf

Lake XP Module Presets 27Sep24.zip

LEA Speaker Tunings are suitable for use with Connect Series ADSP amplifiers running firmware 4.0.0.0 or later. Note that non-ADSP Connect Series amplifiers do not have the necessary DSP resources to create Fulcrum loudspeaker presets and are not supported.

Connect Series ADSP

LEA SharkWare Speaker Tunings 23Sep24 README.pdf

LEA SharkWare Speaker Tunings 23Sep24.zip

Device Settings for Fulcrum Acoustic loudspeakers were created with System Engineer v7.03.04 software. Each .dse file contains presets for a family of loudspeakers, e.g. CX Series or VLF Install Series.

System Engineer v7.03.04

Linea Research Device Settings 20Aug24 README.pdf

Linea Research Device Settings 20Aug24.zip

Powersoft Level 1 Entity Preset files (*.pam) were created using Armonía ProAudioSuite 2.11.4 software. They are suitable for use with DSP-equipped K and Legacy Duecanali Series amplifiers running firmware 5.3.7 or later.

Armonía ProAudioSuite 2.11.4

Powersoft L1 Entity Presets 19May21 README.pdf

Powersoft L1 Entity Presets 19May21.zip

Containers for Fulcrum Acoustic loudspeakers were created with  Q-Sys Designer software. The Containers will appear in the User Component Library on the right side of the Q-Sys workspace.

Q-Sys Designer

Q-Sys Containers 29Aug24 README.pdf

Q-Sys Containers 29Aug24.zip

Check your control software...Using London Architect? Download this file.  If using Audio Architectsee below.Macros for Fulcrum Acoustic loudspeakers were created with London Architect Version 6.00 R5 software. Note that the FIR filters in the Macros require London Processors to be set to a 48 kHz sample rate.

London Architect Version 6.00 R5

London 48k Macros 29Aug24 README.pdf

London 48k Macros 29Aug24.zip

Check your control software... Using Audio Architect?  Download this file.  If using London Architect see above.Sub Configurations for Fulcrum Acoustic loudspeakers were created with Audio Architect  v2.55 software. Note that the FIR filters in the Macros require London Processors to be set to a 48 kHz sample rate.

Audio Architect  v2.55

London 48k Sub Configurations 29Aug24 README.pdf

London 48k Sub Configurations 29Aug24.zip

Composer Super-modules for Fulcrum Acoustic loudspeakers were created with Composer Version 8.5 software. The Super-modules are compatible with Edge, Radius, Prism, and Solus NX processors.

Composer Version 8.5

Composer Super-modules 29Aug24 README.pdf

Composer Super-modules 29Aug24.zip

Designer Super-modules for Fulcrum Acoustic loudspeakers were created with SymNet Designer V10.07  software. Please contact Symetrix directly for a download link. The Super-modules are compatible with first-generation Solus processors.

Solus Super-modules 13Sep24 README.pdf

Solus Super-modules 13Sep24.zip

Processing for Fulcrum Acoustic loudspeakers was created with Xilica Designer v4.9 software. These Xilica settings will work in Solaro FR1 and QR1 processors.Note that the included FIR filters require the Solaro FR1 processor to be set to a 48 kHz sample rate. The QR1’s sample rate is fixed at 48 kHz only.

Xilica Designer v4.9

Xilica Solaro Processing 02Oct24 README.pdf

Xilica Solaro Processing 02Oct24.zip